Product

BIGTREETECH Manta M4P/M8P v2/M5P Control Board

BIGTREETECH Manta M4P/M8P v2/M5P Control Board

115.95 AUD

An Innovative and Easier Way to Run Your Klipper

BIGTREETECH Manta M4P/M8P/M5P Control Boards are built for Klipper; they allow direct installation of the BIGTREETECH CB1/Raspberry Pi CM4 to run the Linux system, then Klipper.

BTT Manta M4P/M5P/M8P controller display

The B1 core board can be directly mounted on the M8P motherboard.

Board-to-Board Connector

Designed with the same connector as the Raspberry Pi, giving you a confident connection with all versions of CM4 and, definitely, CB1 or CB1 eMMC. A screw-reinforced installation is available, too.

CAN Bus solution with Manta control boards.Manta control board can be connected to water cooling kit.btt manta is perfectly compatible with HDMI screens.
It could connect to ADXL345 via SPI port.BIQU Microprobe can also be used with Manta Boards.TFT35 SPI is a smaller sceen to choose to make it compatible with Manta boards.
The Manta board mounted with CM4 can work with a camera or monitor.btt manta board can also work with other USB cameras.
It shows the M4P/M5P/M8P interface diagram, which includes RGB, fan, and screen ports.
It shows the M8P V2 interface diagram, which includes RGB, fan, and screen ports.

Key Features:

  • Manta M4P

    ✅ Installed with a 32-bit 64MHz ARM® Cortex-M0+ STM32G0BORE chip, more stable and faster.

    ✅ Designed with the same connector as the Raspberry Pi, giving you a confident connection with all versions of CM4, definitely CB1. Also, a screw-reinforced installation is available.

    ✅ TPS5450-5A Power Chip: The 5A output perfectly matches the power supply needs of the Raspberry Pi.

    ✅ It has rich expansion ports and can support various expansion modules, such as BL Touch, LCD screen, RGB light, auto shutdown, etc.

    🌟The M4P & CB1 can be the best choice for Voron V0, Ender 3 etc.

  • Manta M5P

    ✅ Installed with a 32-bit 64MHz ARM® Cortex-M0+ STM32G0B1RET6 chip, more stable and faster.

    ✅ Designed with the same connector as the Raspberry Pi, giving you a confident connection with all versions of CM4, definitely CB1. Also, a screw-reinforced installation is available.

    ✅ It has rich expansion ports and can support various expansion modules, such as BL Touch, LCD screen, RGB light, auto shutdown, etc.

    ✅ TPS5450-5A Power Chip: The 5A output perfectly matches the power supply needs of Raspberry Pi.

    ✅ Selectable CNC fan voltage, 5V/12V/24V.

    ✅ Added eFuse circuit protection. It will disconnect faster on overload and automatically reset if the overload is gone, which will greatly reduce motherboard burnout caused by short circuits or ignition.

    ✅ The reserved CAN bus port can be connected to an EBB CAN, which will simplify the wiring and provide strong anti-interference ability.

    🌟The M5P & CB1 can be the best choice for Voron V0, Ender 3, etc.

  • Manta M8P V2.0

    ✅ Installed with a 32-bit 550MHz ARM® Cortex-M0+ STM32H723ZET6 chip, the frequency is faster.

    ✅ Designed with the same connector as the Raspberry Pi, giving you a confident connection with all versions of CM4, definitely CB1. Also, a screw-reinforced installation is available.

    ✅ It has rich expansion ports and can support various expansion modules, such as BL Touch, LCD screen, RGB light, auto shutdown, etc.

    ✅ TPS5450-5A Power Chip: The 5A output perfectly matches the power supply needs of Raspberry Pi.

    ✅ Selectable CNC fan voltage, 5V/12V/24V.

    ✅ Added eFuse circuit protection. It will disconnect faster on overload and automatically reset if the overload is gone, which will greatly reduce motherboard burnout caused by short circuits or ignition.

    ✅ The reserved CAN bus port can be connected to EBB CAN, which will simplify the wiring and provide strong anti-interference capability.

    Update: All new ID. Added I2C,5V Servo, Expanded IO, and TFT interface. Using a 12V power solution. Optimised 5V power supply circuit.

    🌟The M8P V2.0 & CB1 can be the best choice for Voron 2.4, VzBot, etc.

MIG-5926